Difference between revisions of "Helicopter flight and mission"

From BP Wiki
Jump to: navigation, search
(Helicopter Flight Example)
(General control b-threads)
Line 45: Line 45:
 
== BPJ b-threads ==  
 
== BPJ b-threads ==  
  
=== General control b-threads ===  
+
=== General control b-threads ===
DoColD2U: Controls coloring in the up direction;  
+
DoColD2U: Controls coloring in the up direction;
 
YAxis: Reports when helicopter reaches top or bottom end of wall (ceiling of floor)
 
YAxis: Reports when helicopter reaches top or bottom end of wall (ceiling of floor)
EndColUp: Handle reaching of ceiling. Stop moving vertically, start moving right.  
+
EndColUp: Handle reaching of ceiling. Stop moving vertically, start moving right.
DoRowL2R: Left to right painting - waits for  DoRowRight and then repeatedly requests movement to the right until end of right movement is reached.  
+
DoRowL2R: Left to right painting - waits for  DoRowRight and then repeatedly requests movement to the right until end of right movement is reached.
XAxis: Monitor horizontal coordinates. Report reaching of right and left borders of wall, and report end of movement right to start a new column  
+
XAxis: Monitor horizontal coordinates. Report reaching of right and left borders of wall, and report end of movement right to start a new column
 
DoColU2D: Controls coloring in the up direction
 
DoColU2D: Controls coloring in the up direction
 
EndColDown: Handles reaching the floor - requests a movement to the right
 
EndColDown: Handles reaching the floor - requests a movement to the right
BrushMove: Move the brush right and left (horizontal moves) to create a thicker line and paint continuous area. This b-thread performs its actions between any two vertical moves.  
+
BrushMove: Move the brush right and left (horizontal moves) to create a thicker line and paint continuous area. This b-thread performs its actions between any two vertical moves.
  
  
=== Actuator b-threads
+
=== Actuator b-threads ===
MovingRight, MovingLeft, MovingDown, MovingUp: These b-threads wait for the corresponding move event and call the helicopter API (or the simulator) to cause the actual movement.
+
MovingRight, MovingLeft, MovingDown, MovingUp: These b-threads wait for the corresponding move event and call the helicopter API (or the simulator) to cause the actual movement.
  
=== Color control b-threads
+
=== Color control b-threads ===
ChangePaintingColor: Waits for the need to change color and changes the color randomly.
+
ChangePaintingColor: Waits for the need to change color and changes the color randomly.
 
+
=== Location correction b-threads
+
FixWind: When a report comes in that the helicopter is not where it is supposed to be - stop painting movement and return to last known location. 
+
  
 +
=== Location correction b-threads ===
 +
FixWind: When a report comes in that the helicopter is not where it is supposed to be - stop painting movement and return to last known location.
  
 
=== Environment Simulation ===  
 
=== Environment Simulation ===  

Revision as of 09:21, 15 April 2014

Helicopter Flight Example

This example demonstrates the control of a toy helicopter. The mission here is to paint a wall with different colors. This can be considered as an analogy to a photography mission where a particular area as to be covered.

Requirements

The requirements below were added incrementally, and b-threads were added to deal with each requirement. In the simulator - the painting of the wall is by drawing a line on the screen.


  • The helicopter should go up and down along the wall.
  • When the helicopter reaches the ceiling or the floor it should move to the right
  • Every fixed number of pixels the paint color should be changed
  • Since the line drawn by the helicopter is thin, after every small vertical move, the helicopter should move right and left with horizontal brush strokes, before moving vertically again.
  • The helicopter may move from its present location due to wind.
  • If the helicopter is moved by wind, it should return to its last known location.

In the integration with LSC, two more requirements were added

  • The amount of paint is limited. After a certain number of points is painted - the paint runs out.
  • When paint of a certain color runs out, this color can no longer be used.
  • When all paint colors run out, the helicopter must stop.
  • Paint cans may be re-filled. This is simulated by a user clicking on a button on the screen.

Events

General control events

BeginPainting: Start the painting process StopPainting: End the painting process MoveDown: Move down a fixed number of pixels. EndOfColUp: End painting wall going up DoColDownL Start painting wall going down EndOfColDown: End painting wall going up DoRowRight: Start painting wall going right EndOfRowRight: Stop moving right. ChangeColor: The time has come to change color UpdateArrived: simulate information from a GPS with actual helicopter location

Move Events

The following events indicate the desire to move a fixed number of pixels in the desired direction. These events have a data field - indicating whether the movement is for a mission or for maintenance, which serves in correcting wind shifts.

MoveUp: Move down a fixed number of pixels MoveLeft: Move left a fixed number of pixels MoveRight: Move right a fixed number of pixels DoColUp: Start painting wall going up


BPJ b-threads

General control b-threads

DoColD2U: Controls coloring in the up direction; YAxis: Reports when helicopter reaches top or bottom end of wall (ceiling of floor) EndColUp: Handle reaching of ceiling. Stop moving vertically, start moving right. DoRowL2R: Left to right painting - waits for DoRowRight and then repeatedly requests movement to the right until end of right movement is reached. XAxis: Monitor horizontal coordinates. Report reaching of right and left borders of wall, and report end of movement right to start a new column DoColU2D: Controls coloring in the up direction EndColDown: Handles reaching the floor - requests a movement to the right BrushMove: Move the brush right and left (horizontal moves) to create a thicker line and paint continuous area. This b-thread performs its actions between any two vertical moves.


Actuator b-threads

MovingRight, MovingLeft, MovingDown, MovingUp: These b-threads wait for the corresponding move event and call the helicopter API (or the simulator) to cause the actual movement.

Color control b-threads

ChangePaintingColor: Waits for the need to change color and changes the color randomly.

Location correction b-threads

FixWind: When a report comes in that the helicopter is not where it is supposed to be - stop painting movement and return to last known location.

Environment Simulation

ColorControl: Counts movements and announces the need to change color. Wind: Every certain random number of steps, report a random location of the helicopter